NuTone LA-204WH Bedienungsanleitung PDF herunterladen

This device complies with RSS-210

of Industry Canada. Operation is subject

to the following two conditions: (1) this

device may not cause interference;

and (2) this device must accept any

interference, including interference

that may cause undesired operation

of the device.

Refer to Figures 1 and 2.

1. Locate the Pushbutton next to or near

the door.

Do not mount the pushbutton

on a metal surface.

2. Remove the Pushbutton cover by

inserting the tip of a screwdriver in

the slot at the bottom of the Pushbutton

and then gently rock the Pushbutton

cover apart from the Pushbutton base.

3. Choose a level place to locate the

Pushbutton base.

4. Position the Pushbutton base,

and mark the mounting surface with

a pencil through the two holes in

the Pushbutton.

5. Drill two

⁄16” diameter holes at

the previously marked area.

6. Insert the plastic anchors into

the

⁄16” diameter holes.

7. Place Pushbutton over anchors,

and fasten with two screws provided.

Do not replace cover at this time.

PUSHBUTTON SOUND CODING

Refer to Figure 3.

1. The Receiver strobe light will flash

with any chime sound selected. The

Pushbutton can be coded to sound

one of three chime sounds.

2. Select the desired sound as illustrated

in Figure 3.

3. Position the plastic jumper straps

in the proper location for desired

chime sound.

PUSHBUTTON SECURITY

CODING

Refer to Figure 3.

It is not necessary to change the

security code of the Pushbutton unless

you experience interference from other

wireless devices.

1. To change the security code, remove

any combination of the six plastic

jumper straps.

2. NOTE: Both the Pushbutton and

Receiver codes must match.

BATTERY INSTALLATION

Refer to Figure 3.

1. Position the A23 12 volt battery

as illustrated.

Be sure to observe

polarity (+/–).

INSTALLING PUSHBUTTON

COVER

Refer to Figure 4.

1. Position the Pushbutton cover over

the Pushbutton base. The red light

must be lined up over the hole in the

Pushbutton cover. Firmly press cover

over base.

INSTALLATION & OPERATING INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS!

Wireless Chime with Strobe Light

MODEL: LA-204WH

FIGURE 1

FIGURE 2

TO OPEN COVER

“PUSH”

SCREW HOLE FOR WALL

MOUNTING

SCREW HOLE FOR WALL

MOUNTING

–

ONE NOTE

TWO NOTE

WESTMINSTER

SECURITY

CODE SETTING

FIGURE 3

SOUND SELECTION

12V “A23”

BATTERY

LED

FIGURE 4

–

MOUNTING THE PUSHBUTTON TRANSMITTER

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - MODEL: LA-204WH

This device complies with RSS-210 of Industry Canada. Operation is subjectto the following two conditions: (1) thisdevice may not cause interference;

Seite 2 - PREPARING THE RECEIVER

+–654321SECURITYCODE SETTINGTROUBLESHOOTING GUIDEPREPARING THE RECEIVERRECEIVER SECURITY CODINGRefer to Figure 5.Changing the Security Code in not nec

Seite 3 - MODÈLE: LA-204WH

Cet appareil est conforme à la normeCNR-210 d’industrie Canada. Sonfonctionnement est assujetti aux deuxconditions suivantes: (1) Cet appareil ne doit

Seite 4 - PRÉPARATION DU RÉCEPTEUR

4820 Red Bank Road, Cincinnati, Ohio 45227Imprimé aux Chine, Rev. 4/05, PiéceNo. 83044+–654321REGLAGE DU CODE DE SECURITEGUIDE DE DÉPANNAGEON1 2 3 4 5

Seite 5 - MODELO: LA-204WH

Este dispositivo cumple con la normaRSS-210 de “Industry Canada”. Sufuncionamiento se encuentra sujeto a las dossiguientes condiciones: (1) este dispo

Seite 6 - PREPARACION DEL RECEPTOR

+–654321REGLAGE DU CODE DE SECURITEGUIA DE DETECCION Y SOLUCION DE PROBLEMASON1 2 3 4 5 6FIGURA 5PROBLEMA1. La campana nosuena.• Revise las pilas y la

Kommentare zu diesen Handbüchern

Keine Kommentare

NuTone LA-204WH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein NuTone LA-204WH herunter. NuTone LA-204WH User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein NuTone LA-204WH